Buy 2 components and get 4 free cables. Free shipping on all orders over $700. We will be closed on Good Friday (March 29).

0

Your Cart is Empty

Headphone Amplifiers - Part 1

Headphone Amplifiers - Part 1

By John Siau

March 14, 2014

Headphone Amplifiers - Part 1

Specifications are Only Part of the Story!

A couple years ago, some of us at Benchmark noticed a weird discrepancy between our HPA2 headphone amp (built into our DAC1 and DAC2) and some comparably-priced headphone amps. The advertised specifications of all the amps were basically the same, but they sounded noticeably different. Benchmark launched a detailed investigation to identify the differences. The results were surprising and are detailed in "An Examination of Headphone Amplifier Performance Specifications", a white paper by John Siau.

If you care to read the whole whitepaper, you can follow the link above. Otherwise, please continue reading the summary presented in this blog post. Either way, our findings were the same:

We tested three high-quality pro-audio headphone amplifiers with built-in D/A converters. All three had similar published specifications. All units are priced between $1000 and $2000. We verified that the manufacturer’s specifications were accurate, but we have shown that these published specifications are not sufficient to tell the whole story. In this case, the published specifications were not a good representation of typical operating conditions.

The key to the riddle is that all of the published measurements were made with an ideal resistive load. Performance changed dramatically when headphones were connected in place of the resistor loads. With actual headphones loading the amplifiers, the specifications mirrored what we had experienced in listening tests. There were significant differences in the measured performance of the three units when driving headphones, but not when driving resistive loads. We found that our subjective listening tests were validated by the measurements when the tests accurately reflected real-world conditions.

It would be nice if we could build headphones that would behave like an ideal resistor. This would make a headphone amplifier's job easy. Unfortunately, electro-mechanical transducers are far from ideal. The burden falls squarely on the headphone amplifier. As it turns out, headphone amplifiers are not created equal:

In order to make a fair test, we compared the HPA2  (again, included with our DAC1 and DAC2) to comparably spec’d headphone amps costing between $1,000 to $2,000 - not inexpensive models you'd expect to be deficient. All these amplifiers had similar “ideal” specs, but how would they hold up in real-world tests? We wanted to find out.

Headphone Output at Maximum Gain, -3 dB FS Digital Input, No Load THD+N vs Frequency

You can see in the graph above, the ideal test, everything is basically even. None of the three amps show much distortion. Without actually running the signal into a load, the Total Harmonic Distortion + Noise (THD+N) is comparable. While the HPA2  measure slightly better than the others, you probably wouldn't hear a difference between these amplifiers in this ideal world. These are the measurements/specifications that manufacturers show consumers.

Headphone Output at 500 mW into 60 Ohm Load THD+N vs FrequencyIn our second test we added a 60-Ohm resistive load to simulate headphone loading.  Notice that distortion begins to increase in the non-HPA2 amplifiers (green and magenta curves). In contrast, the performance of the HPA2  is nearly unchanged when driving a 60-Ohm resistor (blue curve).

 

Headphone Output at 500 mW into Sony MDR-V6 Headphones THD+N vs Frequency

In our third test, we replaced the 60-Ohm resistor (ideal load) with a pair of 60-Ohm headphones. Distortion rose significantly in the non-Benchmark headphone amplifiers. The 60-Ohm headphones do not behave like 60-Ohm resistors. Clearly the other two amplifiers were having difficulty controlling the headphone transducers. In contrast, the HPA2  measured almost the same as it did in the unloaded conditions (1st test).

This third graph shows the THD+N for the three amplifiers while driving a pair of Sony MDR-V6. The Sony headphones aren’t extremely hard to drive, but they do tax the performance of the non-Benchmark amplifiers.

All three headphone amplifiers have enough power to drive the MDR-V6 headphones at their 500 mW rated power. Nevertheless, units 2 and 3 were unable to fully damp the mechanical resonances of these popular headphones. Consequently, units 2 and 3 show significant distortion at low frequencies.

Units 2 and 3 produce audible levels of distortion when driving the popular Sony MDR-V6 headphones. Clearly these two amps are not able to maintain control over the headphone drivers. Distortion can color the voicing of the headphones and cause listener fatigue.This correlated with the original listening tests that prompted this investigation.

In conclusion, all three of these headphone amps have the same specifications under ideal loads, but they don’t perform the same when driving headphones.

Download the full white paper:

"An Examination of Headphone Amplifier Specifications" - John Siau

Recommended reading:

More information on headphones and headphone amplifiers can be found here

If you’d like to learn more, get in touch with someone at Benchmark, and we’d be happy to answer your questions. We work hard to develop products that perform and measure well under all real-world conditions - not just selected ideal conditions.


Also in Audio Application Notes

Closeup of Plasma Tweeter

Making Sound with Plasma - Hill Plasmatronics Tweeter

by John Siau June 06, 2023

At the 2023 AXPONA show in Chicago, I had the opportunity to see and hear the Hill Plasmatronics tweeter. I also had the great pleasure of meeting Dr. Alan Hill, the physicist who invented this unique device.

The plasma driver has no moving parts and no diaphragm. Sound is emitted directly from the thermal expansion and contraction of an electrically sustained plasma. The plasma is generated within a stream of helium gas. In the demonstration, there was a large helium tank on the floor with a sufficient supply for several hours of listening.

Hill Plasmatronics Tweeter Demonstration - AXPONA 2023

While a tank of helium, tubing, high voltage power supplies, and the smell of smoke may not be appropriate for every living room, this was absolutely the best thing I experienced at the show!

- John Siau

Read Full Post
Benchmark AHB2 Power Amplifier

Audio Calculators

by John Siau June 04, 2023

We have added an "Audio Calculators" section to our webpage. Click "Calculators" on the top menu to see more like these:

THD % to dB Converter

Results update on input change.

Results

THD dB to % Converter

Results update on input change.

Results

Read Full Post
Benchmark AHB2 Power Amplifier

System Performance Calculations

by John Siau June 03, 2023

If an audio system is composed of multiple components, we may have detailed specifications for each component, but we will not know the performance of the combined system without doing some calculations. You may have questions such as these:

  • Will my audio system produce audible noise?
  • Will my audio system produce audible distortion?
  • How will my audio components work together as a system?
  • How loud will my audio system play?

Use Benchmark's online audio calculators to find answers!

For example, if we know the output power of an amplifier, as well as the sensitivity and impedance of our loudspeakers, we can calculate the maximum sound pressure level that our system can produce.

Peak SPL Calculator

Results update on input change.

Results

This application note provides interactive examples that help to answer the questions listed above.

Read Full Post